OCH29867
Single-phase Full-wave Pre-driver
- Motor typeSingle Coil
- Operating voltage4.5V~18V
- Max Lock CurrentBuilt-in Current Limiting
- Fan Safety Rated CurrentExternal Config
- PackageSSOP-16L
- Operating Temperature-40℃~125℃
-
Overview
-
Features
-
Specifications
-
Package & Ordering
-
Apply
overview
OCH29867 is a single-phase driving motor pre-driver with the variable speed function compatible with external PWM signal. With a few external parts, a highly-efficient and highly-silent variable drive fan motor with low power consumption can be achieved.
This product is best suited for driving of the server requiring large air flow and large current and the fan motor of consumer appliances.
OCH29867 is available in TSSOP-16L package and is rated over the -40°C to 125°C.
Applications
Industrial fans, server fans, welding machine fansPurifier fan, mining machine fanSweeper fan, equipment fanBrushless DC fan
features
-
Direct drive P/N MOSFET
-
Speed controllable by DC voltage
-
Speed controllable by PWM input signal
-
Soft start, and the time can be set externally
-
FG speed signal output or RD signal output
-
Under Voltage Protection
-
Current Limit Protection
-
Lock Protection and Auto Restart Function
-
Over Temperature Protection
-
Adopting encapsulated TSSOP-16L
-
ROHS Compliant
Specifications
Type
Parameter
Type
Parameter
-
Motor typeSingle Coil
-
Operating voltage4.5V~18V
-
Max Lock CurrentBuilt-in Current Limiting
-
Fan Safety Rated CurrentExternal Config
-
PackageSSOP-16L
-
Operating Temperature-40℃~125℃
-
Sensitivity (Gauss)External Hall±15
-
PWM Speed ControlDC PWM
-
Min Speed Setting√
-
Lock Auto-Restart√
-
SilentGood
-
Short Circuit Protection√
Package & Ordering
Ordering Information
| Part Number | Package Type | Packing Qty. | Temperature | Eco Plan | Lead |
|---|---|---|---|---|---|
| OCH29867FAE | TSSOP-16L | 2500pcs/Reel | -40 ~ +125℃ | ROHS | Cu |
Package & Pin Definition
| Pin Number | Pin Name | Function |
|---|---|---|
| 1 | OUT2P | Second channel P-type driver output. Open-drain output, must be connected with pull-up resistor to drive external power devices in operation |
| 2 | OUT2N | Second channel N-type driver output. Push-pull output to drive external power devices |
| 3 | VCC | Power supply |
| 4 | CS | Current limiter indicator. Fixed to 0.2V internally. maximum allowable current is decided by external sample resistance. When the voltage of this pin exceeds 0.2V, the output will be shut down by current limit. If this function is not used, connect this pin to ground directly |
| 5 | RMIN | Shutdown point setting terminal connect it to VREF when disused. In case it is tied to other power supply for controlling, an isolated resistor is necessary |
| 6 | Filter | Speed control terminal by DC voltage. It is full speed mode when connected to ground and shut down when the voltage exceeds 3V. Moreover, a low pass network is necessary to transfer PWM to DC level |
| 7 | PWM | PWM signal input. The IC can be controlled by external PWM input signal, when a capacitor is placed between Filter and GND. PWM input frequency is 0.5kHz to 50kHz |
| 8 | FG/RD | Rotation Speed Output or Rotation Detection Output |
| 9 | HIN- | Hall sensor negative input. To prevent noise, this pin is recommended to be placed as close as possible to Hall circuit. If necessary, a capacitor may be added between HIN+ and HIN- to reduce the influence caused by noise |
| 10 | HIN+ | Hall sensor positive input. To avoid noise, this pin is recommended to be placed as close as possible to Hall circuit |
| 11 | SET | VSET ≥2.5V, select Pin8 for FG output; VSET<2.5V, select Pin8 for RD output |
| 12 | SS | Linear start terminal. this pin is connected to VREF externally via a capacitor of 0.47µF to 1µF which enables fan start steadily. Start time is dependent to the capacitance. If linear start function is not used, connect this pin to ground |
| 13 | VREF | 5V voltage reference |
| 14 | GND | Ground for circuit control |
| 15 | OUT1N | First channel N-type driver output. Push-pull output to drive external power devices |
| 16 | OUT1P | First channel P-type driver output. Open-drain output, must be connected with pull-up resistor to drive external power devices in operation |