我们非常重视您的个人隐私,当您访问我们的网站时,请同意使用的所有cookie。有关个人数据处理的更多信息可访问《隐私条款》

OCH29867P

Single-phase Full-wave Pre-driver

  • Motor typeSingle Coil
  • Operating voltage4.5V~18V
  • Max Lock CurrentBuilt-in Current Limiting
  • Fan Safety Rated CurrentExternal Config
  • PackageSSOP-16L
  • Operating Temperature-40℃~125℃
TSSOP-16L-EP.jpg
  • Overview
  • Features
  • Specifications
  • Package & Ordering
  • Apply

overview

OCH29867P is a single-phase driving motor pre-driver with the variable speed function compatible with external PWM signal. With a few external parts, a highly-efficient and highly-silent variable drive fan motor with low power consumption can be achieved.

This product is best suited for driving of the server requiring large air flow and large current and the fan motor of consumer appliances.

OCH29867P is available in TSSOP-16L package and is rated over the -40°C to 125°C.

Applications

Industrial fans 、server fans 、 welding machine fansPurifier fan、mining machine fanSweeper fan、equipment fanBrushless DC fan

features

  • Direct drive P/N MOSFET
  • Speed controllable by DC voltage
  • Speed controllable by PWM input signal
  • Soft start, and the time can be set externally
  • FG speed signal output or RD signal output
  • Under Voltage Protection
  • Current Limit Protection
  • Lock Protection and Auto Restart Function
  • Over Temperature Protection
  • Adopting encapsulated TSSOP-16L
  • ROHS Compliant

Specifications

Type
Parameter
Type
Parameter
  • Motor type
    Single Coil
  • Operating voltage
    4.5V~18V
  • Max Lock Current
    Built-in Current Limiting
  • Fan Safety Rated Current
    External Config
  • Package
    SSOP-16L
  • Operating Temperature
    -40℃~125℃
  • Sensitivity (Gauss)
    External Hall±15
  • PWM Speed Control
    DC PWM
  • Min Speed Setting
    √
  • Lock Auto-Restart
    √
  • Silent
    Good
  • Short Circuit Protection
    √

Package & Ordering

Ordering Information

Part NumberPackage TypePacking Qty.TemperatureEco PlanLead
OCH29867PFAETSSOP-16L2500pcs/Reel-40 ~ +125℃ROHSCu

Package & Pin Definition

Pin NumberPin NameFunction
1OUT2PSecond channel P-type driver output. Open-drain output, must be connected with pull-up resistor to drive external power devices in operation
2OUT2NSecond channel N-type driver output. Push-pull output to drive external power devices
3VCCPower supply
4CSCurrent limiter indicator. Fixed to 0.2V internally. maximum allowable current is decided by external sample resistance. When the voltage of this pin exceeds 0.2V, the output will be shut down by current limit. If this function is not used, connect this pin to ground directly
5RMINMinimum speed setting terminal connect it to VREF when disused. In case it is tied to other power supply for controlling, an isolated resistor is necessary
6FilterSpeed control terminal by DC voltage. It is full speed mode when connected to ground and shut down when the voltage exceeds 3V. Moreover, a low pass network is necessary to transfer PWM to DC level
7PWMPWM signal input. The IC can be controlled by external PWM input signal, when a capacitor is placed between Filter and GND. PWM input frequency is 0.5kHz to 50kHz
8FG/RDRotation Speed Output or Rotation Detection Output
9HIN-Hall sensor negative input. To prevent noise, this pin is recommended to be placed as close as possible to Hall circuit. If necessary, a capacitor may be added between HIN+ and HIN- to reduce the influence caused by noise
10HIN+Hall sensor positive input. To avoid noise, this pin is recommended to be placed as close as possible to Hall circuit
11SETVSET ≥2.5V,select Pin8 for FG output; VSET<2.5V,select Pin8 for RD output
12SSLinear start terminal. this pin is connected to VREF externally via a capacitor of 0.47µF to 1µF which enables fan start steadily. Start time is dependent to the capacitance. If linear start function is not used, connect this pin to ground
13VREF5V voltage reference
14GNDGround for circuit control
15OUT1NFirst channel N-type driver output. Push-pull output to drive external power devices
16OUT1PFirst channel P-type driver output. Open-drain output, must be connected with pull-up resistor to drive external power devices in operation

Series of product applications